Spring repair · Lake Mary, Florida

Garage Door Spring Repair Lake Mary FL

If you heard a loud bang and the door suddenly feels too heavy to lift, a spring likely snapped. Get a safe, correct replacement so the door is balanced, the opener is protected, and you can use your garage again.

✓Torsion and extension springs ✓Measured for correct spring sizing ✓Balance and safety checked
Technician safely working on a residential garage door torsion spring system with winding bars

Broken spring safety

Fast help for broken garage door springs in Lake Mary

Searching for garage door spring repair Lake Mary FL usually means the door will not open, it opened partway and stopped, or you noticed a gap in the spring above the door. Springs do the heavy lifting. When one breaks, the full weight of the door shifts to you and to the opener, which is why forcing it can burn out the motor or strip gears.

Lake Mary Garage Door Repair handles garage door spring replacement in Lake Mary for both common spring types: torsion springs mounted on a steel shaft above the door and extension springs along the tracks on many older setups. A quick on-site inspection confirms the spring type, door weight, correct spring size, and whether related hardware needs attention.

If you also suspect the opener is straining or the door is off-track, start with a full service check from garage door repair in Lake Mary. A broken spring often looks like an opener problem, but the spring is the root cause.

Warning signs

What a broken spring looks like (and what to do right now)

Most homeowners notice one of these signs:

  • ✓A sharp bang from the garage, then the door will not lift.
  • ✓The opener runs but the door barely moves or reverses.
  • ✓The door feels extremely heavy by hand.
  • ✓On torsion systems, there is a clear separation or gap in the coil above the door.
  • ✓On extension systems, a spring may be stretched out or hanging while the safety cable contains the parts.

What to do next in Lake Mary:

  1. 1) Leave the door closed if possible. A door with a broken spring can drop unexpectedly.
  2. 2) Do not pull the emergency release and try to “muscle” the door open unless you have enough help and can control the weight.
  3. 3) Keep vehicles out until the spring is replaced and the door is balanced.

Spring work involves stored torque. The safe fix is replacing the spring with the correct size, setting proper winding turns and balance, and checking cables, drums, bearings, and rollers.

CALL NOW: (407) 456-8884
Close view of a technician servicing a secured residential torsion spring assembly

Complete spring service

What is included in garage door spring replacement

Correct spring sizing

The right wire size, inside diameter, and length are matched to the door weight and height so the door stays balanced instead of drifting up or slamming down.

Safe removal and install

The door is secured, old springs are unwound or de-tensioned properly, and the new spring set is installed with the right orientation for your door.

Balance and force check

After replacement, the door is tested by hand for balance and the opener travel and safety reversal are checked so the opener is not doing the lifting.

Hardware inspection

Cables, drums, center bearing area, end bearings, and track alignment are checked because spring failure can reveal wear elsewhere.

Noise and friction reduction

Rollers and hinges are checked for binding. A properly balanced door usually runs quieter and puts less strain on moving parts.

Inspection to completion

How Lake Mary Garage Door Repair handles spring repair, step by step

A measured process protects the door, matches the replacement correctly, and verifies the final balance.

01

Inspect and measure

We identify the spring system, check the door's condition, and measure for the correct replacement springs rather than guessing based on door width alone.

02

Secure the door and relieve tension

The door is clamped in place and tension is removed in a controlled way so the shaft, cables, and brackets can be serviced safely.

03

Replace the spring set

We install the new torsion or extension springs, confirm orientation, and address any obvious issues that would prevent proper balance.

04

Balance test and final safety check

We test the door by hand for neutral balance, then verify smooth travel and check opener settings so the door lifts reliably without strain.

CALL NOW: (407) 456-8884

Spring repair details

Spring repair work examples (what to expect)

The service centers on correct sizing, controlled installation, related hardware inspection, and a final balance test.

Measured replacement

Spring selection is based on the door’s height, weight, spring system, and hardware, not door width alone.

Controlled tension work

The door is secured before old components are unwound or de-tensioned.

Supporting hardware check

Cables, drums, bearings, brackets, rollers, and track condition are reviewed for related wear.

Balanced final operation

The finished door is checked by hand and with the opener to confirm smooth travel without excessive opener strain.

CALL NOW: (407) 456-8884

Common questions

Garage door spring repair Lake Mary FL: FAQs

Answers about spring safety, replacement choices, timing, and opener strain.

Is it safe to open my garage door with a broken spring?

It is not safe to lift a garage door with a broken spring unless you can fully control the door's weight and keep it from dropping. Springs counterbalance the door, so once one breaks the door can be unexpectedly heavy and can slam shut. The safest move is to keep the door closed and have the spring replaced and the door rebalanced.

Do you replace one spring or both springs at the same time?

On two-spring torsion systems, replacing both is often the most practical choice because the springs are typically the same age and cycle life. Replacing both helps keep the door balanced side-to-side and reduces the chance of a second failure soon after. After inspecting your setup, we can recommend whether one or both springs should be replaced for your door.

What is the difference between torsion and extension springs?

Torsion springs mount above the door on a metal shaft and lift the door by twisting and applying torque through drums and cables. Extension springs run along the tracks and lift by stretching as the door closes, typically with safety cables running through them. The replacement approach, parts, and adjustment method differ, so identifying the spring type is the first step.

Why did my spring break so suddenly?

Springs usually fail from metal fatigue after repeated cycles of opening and closing, and the break can sound sudden because stored tension releases at once. Rust, lack of lubrication, and an unbalanced or binding door can also increase stress on the spring.

Can a broken spring damage my garage door opener?

Yes. When the spring is broken, the opener may try to lift the full door weight, which can overheat the motor, strip gears, or cause the trolley and rail to strain. If your opener started acting up, it is worth checking opener force settings and door balance after replacement.

If your garage door will not lift or feels dangerously heavy, getting the spring replaced quickly prevents damage to the opener and reduces the risk of the door dropping or coming off balance.

CALL NOW: (407) 456-8884

Schedule spring repair in Lake Mary

Tell Lake Mary Garage Door Repair what the door is doing (bang, stuck closed, crooked lift, opener strain) and we will confirm the spring type, replace it safely, and set the door balance so it operates normally again.